WhatsApp us now
Message now
Message now
Have a call now
+60 11 – 1061 9565
+60 11 – 1061 9565
KIMMU® Temporary Fence (Safety Guardrail) is a practical temporary fencing solution designed for site safety, traffic control, and temporary access management. It provides a visible physical barrier that helps organise work zones, guide pedestrian flow, and improve safety at construction sites, maintenance areas, warehouses, and public spaces.
Built with a sturdy steel frame and wire mesh infill, the guardrail offers reliable durability for repeated use. Its powder coated yellow finish with black hazard panel enhances visibility, making it suitable for both indoor and outdoor temporary applications.
KIMMU® Temporary Fence (Safety Guardrail) is easy to install, relocate, and store, making it an efficient solution for contractors, industrial users, and facility operators.
Key Features
| Size | 1.8M × 1.8M |
| Mesh Size | 55MM × 55MM |
| Colour | Yellow & Black |
| Finishing | Powder Coating |
KIMMU® Temporary Fence (Safety Guardrail) is commonly used for:
Woven Geotextile are manufactured with high tensile strength and low elongation for erosion control, stabilization and aggregate separation. Offering an increased grab tensile strength, woven geotextile fabrics offer a robust design that allows them to be used in most of the earthwork projects
Features:
General Application as below:
United Geo Non Woven Geotextile is engineered to form a strong fabric designed to cater for general earthwork projects application such as drainage, filtration, separation, protection, stabilisation and reinforcement.
Festures:
General Application as below:
| Model Propeties | Tensile Strength | Tensile Elongation At Break (%) | CBR Puncture Strength (kN) | Flow Rate at 50mm Head (l/m2/s) | Nominal Mass (g/m2) | Thickness (mm) |
| TEST METHOD | ASTM D 4595-11 | ASTM D 4595-11 | ISO 12236 : 2006 | ISO 11058 : 2010 | ISO 9864 : 2005 | ISO 9863-1 : 2016 |
| UG 10 | 7.5 | 80/60 | 2.01 | 130 | 105 | 0.9 |
| UG 20 | 9.5 | 80/60 | 2.01 | 120 | 125 | 1 |
| UG 30 | 11.5 | 75/35 | 1.75 | 100 | 155 | 1.5 |
| UG 40 | 13.5 | 75/35 | 2.1 | 90 | 180 | 1.6 |
| UG 50 | 17 | 80/50 | 3.373 | 90 | 200 | 1.75 |
| UG 60 | 19 | 80/50 | 2.9 | 72 | 250 | 2.2 |
| UG 70 | 21.5 | 80/50 | 3.3 | 65 | 285 | 2.5 |
| UG 80 | 24 | 80/50 | 3.85 | 55 | 325 | 2.9 |
| UG 90 | 28 | 80/50 | 4.25 | 50 | 400 | 3.2 |
| Composition | 100% Polyester or Polypropylene, UV Stabilised Nonwoven Needle Punched | |||||
The value shown above are indicative and average values
Tolerance : Mechanical Properties +- 10%
Hydraulic Properties +- 10%
KIMMU® High Load Jumbo Coil Nail: JUMBO coil nails are used in automated machinery with jumbo magazine. The quantity of nails may range from 1,000 to 3,000 nails per coil. Our production capability ensures the jumbo coil are available with almost any combination of standard length, diameters and finish and packed in standard KIMMU carton box.
| Standard Specification | |
|---|---|
| Angle | 15 degrees flat |
| Length | 32mm – 75mm |
| Diameter | 2.1mm – 3.1mm |
| Shank | Smooth/Screw/Ring |
| Point | Diamond/Blunt/Chisel |
| Finish | Bring/Electro Galvanized |
| Quantity Packing | 3000pcs/coil 2 coils/carton |
Custom made service available:
- Quantity of nail per coil
- Packing and packing quantity
- Tailor made coil nail can be produced to accommodate client’s requirement, please get in touch with us to find out more.
CEM-MIX: WALL & FLOOR TILE ADHESIVE (C2 & C2 TE)
CEM MIX TILE ADHENSIVE is a prepacked mix formulated with selected silica sand
cement and chemical additives.
CEM MIX TILE ADHENSIVE provides a high quality and strong adhesive for tiling on concrete substrate & cement rendered surface. It is suitable for mosaics, marble, granite, ceramics & homogeneous tiles.
CEM MIX TILE ADHENSIVE requires only adding water and through mixing at site.
Highly recommended for interior or exterior application as a thick bed mortar for laying of :
How to use?
SURFACE PREPARATION
All concrete should be free of loose particles, dust, dirt, oil, grease and other contaminations. Wet surfaces if necessary before laying.
APPLICATION
Recommended thickness is between 1-5mm. Notched trowel is recommended to ensure good bond and reduce wastage.
MIXING
Slowly add powder into a pail with water and mix with a slow speed hand-held electric stirrer or drum mixer. Mix for 4-5 minutes until a desired consistent workability is achieved. Mix should be lump free. Do not add water to unused mix.
Benefits:
| Technical Data | |
|---|---|
| Colour | Grey/White |
| Working Time | 45 minutes |
| Pull-Off Adhesion | 1.2 N/mm2 |
| Compressive Strength | 10.5 N/mm2 |
| Water Demand | 6.5/7.0 liters/25kg bag |
| Packing | 25kgs/bag |
| Coverage (approx.) | 2.0m2/5mm thickness/25kg |
CEM-COAT: SKIM COAT FINE 388 GREY / WHITE
SKIM COAT FINE is a prepacked mix formulated with selected fine fillers, cement and chemical additives.
SKIM COAT FINE provides a high quality and smooth finishing coat on ceiling and wall or any concrete surfaces.
SKIM COAT FINE requires only adding water and through mixing at site.
Highly recommended for interior application only :
How to use?
SURFACE PREPARATION
All surfaces should be free of loose particles, dust, dirt, oil, grease and other contaminations. Wet surfaces before laying.
APPLICATION
Recommended thickness for each application is between 1-2mm. Allow for sufficient curing time before applying subsequent coat.
MIXING
Slowly add powder into a pail with water and mix with a slow speed hand-held electric stirrer or drum mixer. Mix for 4 minutes until a desired consistent workability is achieved. Mix should be lump free. Do not add water to unused skim coat mix.
Benefits:
| Technical Data | |
|---|---|
| Colour | Grey/White |
| Working Time | 50 minutes |
| Pull-Off Adhesion | 0.82 N/mm2 |
| Compressive Strength | 5.4 N/mm2 |
| Water Demand | 11.2 liters/40kg bag 7 liters/25kg bag" |
| Packing | 25kgs/bag or 40kgs/bag |
| Coverage (approx.) | 32 m2/1 mm thickness/40kg 20 m2/1 mm thickness/25kg |
CEM-MIX: WALL & BRICK MORTAR PLASTER
CEM MIX WALL & BRICK MORTAR PLASTER is a prepacked mix formulated with selected silica sand cement and chemical additives.
CEM MIX WALL & BRICK MORTAR PLASTER provides a high quality consistent mortar or render with superior bonding.
CEM MIX WALL & BRICK MORTAR PLASTER requires only adding water and through mixing at site and can be used in place of conventional or on-site mixing.
Highly recommended for interior or exterior application as a thick bed mortar for laying of :
Benefits:
How to use?
SURFACE PREPARATION
All concrete must be free of loose particles, dust, dirt, oil, grease and other contaminations. Wet surfaces before laying.
APPLICATION
Recommended thickness for each application is between 6-20mm. For application above 20mm thickness, a 2-coat application method is recommended.
MIXING
Slowly add powder into a pail with water and mix with a slow speed hand-held electric stirrer or drum mixer. Mix for 4-5 minutes until a desired consistent workability is achieved. Mix should be lump free.
| Technical Data | |
|---|---|
| Colour | Grey |
| Working Time | 35 minutes |
| Water Retentivity | 99% |
| Compressive Strength | 12.0 N/mm2 |
| Water Demand | 6.6 liters/40kg bag |
| Packing | 25kgs/bag or 40kgs/bag |
| Coverage (approx.) | 2.4 m2/10mm thickness/40kg |
CEM-COAT: SKIM COAT BASE 380 GREY / WHITE
SKIM COAT BASE is a prepacked mix formulated with selected fine fillers, cement and chemical additives.
SKIM COAT BASE provides a high quality and good adhesion performance to receive fine finishing on ceiling and wall or any concrete surfaces.
SKIM COAT BASE requires only adding water and through mixing at site.
Highly recommended for interior or exterior application on:
How to use?
SURFACE PREPARATION
All surfaces should be free of loose particles, dust, dirt, oil, grease and other contaminations. Wet surfaces before laying.
MIXING
Slowly add powder into a pail with water and mix with a slow speed hand-held electric stirrer or drum mixer. Mix for 4 minutes until a desired consistent workability is achieved. Mix should be lump free. Do not add water to unused skim coat mix.
APPLICATION
Recommended thickness for each application is between 2-3mm. Allow for sufficient curing time before applying subsequent coat.
Benefits:
| Technical Data | |
|---|---|
| Colour | Grey/White |
| Working Time | 50 minutes |
| Pull-Off Adhesion | 0.82 N/mm2 |
| Compressive Strength | 10.5 N/mm2 |
| Water Demand | 11.2 liters/40kg bag |
| Packing | 25kgs/bag or 40kgs/bag |
| Coverage (approx.) | 14 m2/2mm thickness/40kg 8.75 m2/2mm thickness/25kg |
Level 30, The Garden North Tower, Mid Valley City, Lingkaran Syed Putra, 59200 Kuala Lumpur, Malaysia.
| Phone No.: | +60 11 - 1061 9565 |
| Fax No.: | +60 7 – 428 0888 |
| Email: | enquiry@kimmu.com.my |
| Web: | www.kimmu.com.my |
